- Help Center
- Profitec Pro 700
- Panel Removal & Boiler Drain
-
Getting Started
-
Espresso 101
-
Warranty, Ordering & Returns
-
Like New & Trade-In Program
-
General Troubleshooting
-
LUCCA A53 Direct Plumb
-
LUCCA A53 Mini/Mini Vivaldi
-
LUCCA M58 by Quick Mill
-
LUCCA X58 by Quick Mill
-
LUCCA Solo
-
LUCCA Accessories
-
LUCCA S58 by Profitec
-
La Marzocco Linea Mini
-
La Marzocco GS3
-
Lelit Mara X
-
Lelit Bianca
-
Lelit Elizabeth
-
Lelit Victoria
-
ECM Synchronika
-
ECM Special Edition Classika PID
-
ECM Mechanika V Slim
-
ECM Mechanika VI Slim
-
ECM Casa V
-
ECM Puristika
-
Profitec GO
-
Profitec Pro 300
-
Profitec Pro 400
-
Profitec Pro 500
-
Profitec Pro 600
-
Profitec Pro 700
-
Profitec Pro 800
-
Profitec Drive
-
Rocket Appartamento
-
Rocket R58 / Cinquantotto
-
Rocket Giotto
-
Rocket R Nine One
-
Rocket Boxer
-
La Spaziale S2 EK
-
Rancilio Silvia
-
Rancilio Silvia Pro
-
Rancilio Silvia Pro X
-
Sanremo YOU
-
Ascaso Steel DUO
-
Breville Barista Pro
-
Breville Oracle Touch
-
Flair Classic Espresso Maker
-
Flair 58 Pro 2
-
Flair 58 Plus Espresso Maker
-
LUCCA Grinders
-
Baratza Grinders
-
Eureka Grinders
-
ECM Grinders
-
Fellow Grinders
-
Fellow Tally Precision Scale
-
Mahlkönig Grinders
-
DF64 Grinder
-
Quick Mill
-
Izzo Alex Duetto
-
Bezzera BZ10
-
Bezzera Duo DE
-
Bezzera Duo MN
-
Dalla Corte Mina
-
Compak Grinders
-
Dalla Corte Grinders
-
Profitec Grinders
-
Breville Grinders
-
Macap Grinders
-
Fiorenzato Grinders
-
Slayer
-
Eureka Mignon Zero
-
Profitec JUMP
-
Profitec MOVE
Profitec Pro 700: Panel Removal
Below you will find instructions and a video for removing the panels from the Profitec Pro 700 Espresso Machine.
Unplug the machine and let it cool down before following this procedure.
Tools Needed:
- 2.5mm allen wrench
- 3mm allen wrench
1. Remove the water tank from the machine, and then take out the 4 screws in the top panel. It will lift off of the top of the machine.
![Profitec Pro 700: Panel Removal and Wood Panel Installation](https://support.clivecoffee.com/hubfs/Pro_700_Panel_Removal_1.jpg)
2. Tip the machine so that you are able to loosen all 6 screws on the bottom of the machine. It's not required to take them fully out.
![Profitec Pro 700: Panel Removal and Wood Panel Installation](https://support.clivecoffee.com/hubfs/Pro_700_Panel_Removal_2.jpg)
3. Remove the back panel by loosening the 2 screws on either side at the top of the machine, and then pulling the panel straight off the back.
![Profitec Pro 700: Panel Removal and Wood Panel Installation](https://support.clivecoffee.com/hubfs/Pro_700_Panel_Removal_3.jpg)
4. Remove the side panel by loosening the screw near the top front corner of the machine and sliding the screw down and backwards as shown in the picture.
![Profitec Pro 700: Panel Removal and Wood Panel Installation](https://support.clivecoffee.com/hubfs/Pro_700_Panel_Removal_4.jpg)