- Help Center
- LUCCA X58 by Quick Mill
- Panel Removal And Draining Boilers
-
Getting Started
-
Espresso 101
-
Warranty, Ordering & Returns
-
Like New & Trade-In Program
-
General Troubleshooting
-
LUCCA A53 Mini/Mini Vivaldi
-
LUCCA A53 Direct Plumb
-
LUCCA Accessories
-
LUCCA M58 by Quick Mill
-
LUCCA Solo
-
LUCCA Tempo
-
LUCCA X58 by Quick Mill
-
LUCCA S58 by Profitec
-
La Marzocco Linea Mini
-
La Marzocco GS3
-
Lelit Mara X
-
Lelit Bianca
-
Lelit Elizabeth
-
Lelit Victoria
-
ECM Synchronika & Synchronika II
-
ECM Special Edition Classika PID
-
ECM Mechanika V Slim
-
ECM Mechanika VI Slim
-
ECM Casa V
-
ECM Puristika
-
Profitec MOVE
-
Profitec RIDE
-
Profitec JUMP
-
Profitec GO
-
Profitec Drive
-
Profitec Pro 300
-
Profitec Pro 400
-
Profitec Pro 500
-
Profitec Pro 600
-
Profitec Pro 700
-
Profitec Pro 800
-
Rocket Appartamento
-
Rocket R58 / Cinquantotto
-
Rocket Giotto
-
Rocket R Nine One
-
Rocket Boxer
-
La Spaziale S2 EK
-
Rancilio Silvia
-
Rancilio Silvia Pro
-
Rancilio Silvia Pro X
-
Sanremo YOU
-
Ascaso Steel DUO
-
Breville Barista Pro
-
Breville Oracle Touch
-
Flair Classic Espresso Maker
-
Flair 58 Pro 2
-
Flair 58 Plus Espresso Maker
-
LUCCA Grinders
-
WEBER WORKSHOPS Grinders
-
Baratza Grinders
-
Eureka Grinders
-
Eureka Mignon Zero
-
ECM Grinders
-
Fellow Grinders
-
Fellow Tally Precision Scale
-
Mahlkönig Grinders
-
DF64 Grinder
-
Quick Mill
-
Izzo Alex Duetto
-
Bezzera BZ10
-
Bezzera Duo DE
-
Bezzera Duo MN
-
Dalla Corte Mina
-
Compak Grinders
-
Dalla Corte Grinders
-
Profitec Grinders
-
Breville Grinders
-
Macap Grinders
-
Fiorenzato Grinders
-
Slayer
LUCCA X58: Panel Removal
Follow these instructions to remove the panels from your LUCCA X58 for maintenance or repair.
Tools needed:
- Philips head screw driver
NOTE: The machine should be unplugged and cool to the touch before you begin.
1. Remove the cup warming tray, drip tray, and reservoir from the machine:
2. Remove the two screws attached to the back panel with a Philips head screwdriver:
3. Once the two screws are removed, apply pressure to the top of the back panel to release the pop screws:
4. Using a towel to support the group head, carefully tilt the machine on its front to access the screws on the bottom of the machine:
5. Remove the 2 screws on the top:
6. And these 3 screws from the bottom:
7. The left & right side panels have a tab on them that needs to come around and over the top panel:
8. If you need to access the boiler or any internal components, you'll need to remove the reservoir panel. First, remove the nut attached to the expansion valve:
- If you just need to get the side panels off the machine, you can stop here. With a little extra caution, it's perfectly safe to re-install the full reservoir and operate the machine as normal at this point. -
9. If you need more access to the machine's internals, remove the tubing from the inlet and lift the reservoir panel up and off to the side (you shouldn't need to disconnect the wires unless otherwise instructed by a technician.)
Now you have access to the inside of your LUCCA X58!
** If you need to test your machine with the panels off to check for a leak or an electrical issue you can set up the water tank like so (just make sure to reattach the tubing to the reservoir inlet:)