Getting Started

ECM Classika: Setup Guide Video

Congratulations on your new EMC Classika Espresso Machine. Watch our setup video below on this single boiler, PID operated, E61 group head machine to help you get started.

Step 1: Inspect the box and the machine for damage

  • Inspect the box for damage
  • If the box isn’t damaged, support the machine from the group head and bottom of the rear panel, and lift the machine out of the box.
  • Make sure the machine is on a stable, level surface
  • Take the bag off the machine
  • Inspect the machine for any damage
  • If you see any damage, please contact us immediately.

Step 2: Water quality and filling water tank

  • Make sure to use filtered and softened water for your espresso machine
  • Before filling, test the water hardness using the test strip included with the machine.
  • Ideal water hardness is below 50 ppm.
  • Please read The Importance of Water and Your Machine to learn more about our recommendations for water quality.
  • Once your water has been verified, fill the water tank at the back of the machine.

Step 3: Starting your machine and filling the boiler

  • Plug your machine in and turn on the power switch
  • To fill the boiler, first place a small container under the steam wand
  • Lock the joystick down to open the steam wand, and activate the pump with the water switch labeled “P”.
  • When water starts to flow out of the wand the boiler has filled, then flip the P switch down and bring the joystick back to its closed center position. This should take less than one minute. Give the pump a few minutes to rest.
  • Before pulling your first shots we recommend flushing 20oz of water through the steam wand to rinse the boiler. To do this, lock the joystick down, and activate the P switch.
  • Once you’ve flushed enough water, turn off the pump/hot water switch and close the wand.
  • Last, run a small amount of water through your group head–raise the lever until you see a steady stream of water coming through the dispersion screen
  • Insert the spouted portafilter and wait for the machine to come to temperature
  • Pro tip: you’ve used a lot of water, so now is a good time to refill your water reservoir

Step 4: Pulling your first shots

  • Take out the portafilter
  • Grind a full dose of 20 grams of ground coffee
  • Settle the grounds by giving the sides of portafilter a few light taps with your hand, then two firm, downward taps against your counter (Pro tip: a tamping mat is your friend).
  • Tamp the coffee
  • Your goal is not to use a ton of force to jam the coffee into the basket. Your goal is to create a level, even bed of compressed coffee
  • Start with a level tamp. Apply enough pressure that you’ll feel the coffee push back against you (30 lbs).
  • Insert the portafilter into the group head and lift the brew lever to start the shot.
  • We’ll be looking to produce around 1.5 ounces of espressos in 25-30 seconds
  • If you get 1.5 ounces of espresso in less than 25 seconds, adjust your grind finer
  • If it takes longer than 30 seconds, adjust your grind coarser
  • Remember to keep the amount of ground coffee, tamping pressure and liquid espresso the same. Only try to adjust the grind at first. This will keep you from having to chase lots of different variables.

Step 5: Steaming Milk

  • The Classika is a single boiler. To steam milk, you’ll have to switch the boiler to steaming mode
  • Flip the steam switch
  • You’ll have to purge some of the water from the boiler to make room for steam
  • Press the joystick down to purge the wand for 5 seconds, then turn it off and wait twenty seconds
  • Press the joystick down to purge the wand for 5 seconds. Turn it off and wait twenty seconds
  • Purge the steam wand for 5 seconds one last time. By now, you should be seeing plenty of steam coming out of the wand
  • Pro-tip: speed up your process by portioning your milk while you wait for your machine to come to temp
  • To steam insert the steam wand tip into your milk pitcher and open the steam wand using the joystick. For tips on improving your milk steaming, check our Milk Steaming Tutorial here.
  • Once your milk reaches the ideal temperature, bring the joystick back to the off position and turn off the steam switch.
  • To prep the machine for your next espresso, lift the brew lever until a steady flow of water starts coming through the screen (should take around 20-30 seconds). Once the PID reads at your brewing temperature, you’ll be ready to make more fantastic espressos.

Helpful Links